Auxx Lift
$1,495
Lower the storage platform at the push of a button. EASY Installation on Joists and Rafters. Incl. remote
- No lifting or ladders
- Steel aircraft cables (Lift tested to UL-standards)
- Built in the USA - Uses SPAX® PowerLags®
- Low ceiling hanging height - Competitor's lifts require 4+ ft. INCLUDES: Motors with cables, Platform, Hardware, Remote, struts, step-by-step instructions
Cable Extension
Extra Remote Control
Additional hardware Kit
Additional hardware Kit
-The Auxx-Lift can be mounted on any ceiling (rafters/joists/sloped ceiling) THIS KIT IS OPTIONAL: Normally the lift's motors run parallel to the ceiling joists. If you want the motors to run perpendicular to your joists you will need this kit. This additional kit will turn the platform 90 Degrees
$1,495
or
Auxx Lift
- No lifting or ladders
- Steel aircraft cables (Lift tested to UL-standards)
- Built in the USA - Uses SPAX® PowerLags®
- Low ceiling hanging height - Competitor's lifts require 4+ ft. INCLUDES: Motors with cables, Platform, Hardware, Remote, struts, step-by-step instructions

Auxx Lift
General specs
- Model: Auxx-Lift 1400 Auxx-Lift 1600
- Lifting Capacity: Up to 400 lbs Up to 600 lbs
- Max. Travel Distance1: 16 ft 22 ft
- Min. stored height2: 8 in
Roof Support
- Type: (2) 1 5/8" x 60" strut channel
- Fasteners: (8) 5/16" x 4" SPAX© Lag Bolts
- Mounting Area: 5' x 5' over 3 joists/rafters
- Cable: 1/8” Vinyl-coated Steel 7x19 3/16” Vinyl-coated Steel 7x19
- Cable Strength3: 2,000 lbs 4,200 lbs
Operating Requirements
- Switch Voltage: 110V / 120V
- Transmitter: 433.92 MHz
- Electrical Cord: 10 FT / 16 gauge / NEMA 5-15
- Min. circuit size: 15 amp
Platform Specs
- Thickness: 2.5 inches
- Support Frame: C-Channels (15gauge)
- Face material: 3 x 3 galv. Wire Mesh (4gauge)
Motors
- Type: IP44 (T-Motor)
- Rated Power: 235 W 680 W
- Rated Current: 2.2 A 6.0 A
- Voltage / Phase: 100-120V AC / Single
- Duty Cycle @ Max. Capacity: 3 min on, 15 min off4
Size and Weight
- Dimensions: 3ft x 6ft, 3ft x 8ft, 4ft x 6ft, 4ft x 8ft
- Weight: 128 pounds
Available Finishes
What's in the box
- 2 Motors
- Controller
- Remote Control
- 2 C-Strut Channels
- Platform
- Mounting Hardware
1We offer multiple cable length versions. E.g. The 400 lbs version can be equiped with a cable length to allow 16 ft of travel.
2The distance measured from your ceiling to the bottom of the platform when in raised position.
3Ultimate tensile strength
4If you run the Auxx-Lift continously for more than 3 min at a time, the motors will switch off automatically and require to cool down for 15 min or less.
Product gallery
Popular questions
What are the benefits of the Auxx-Lift's design?
What are the lift's electrical requirements?
What is the installation like?
How is the unit installed in relation to the joists?
What is the max. travel distance?
How much clearance do I need above the garage door?
Tools needed
For DIY Installation
Following tools are needed:
- Wrench set - 13/32", 7/16", 23/32"10mm, 11mm, 18mm
- Flathead Screw driver 0.04"x0.1" 1x3mm
- Phillips #1 Screw driver
- Allen Wrench - 3/16", 3/32"5mm, 2.5mm
- Level
- Tape measure
- Pencil
- Drill
- 7/16"11mm socket for drill
- Drill bit - 1/8", 3/16", 9/32"3mm, 5mm, 7mm
- Stud finder
- Line laser
- Digital Multimeter
Header title displayed
Lorem ipsum dolor sit amet, quia non consectetur adipiscing elit.
Start earning